How to change blade on Ryobi table saw?

There is no doubt that blades are one of the most important parts of a table saw. It doesn’t matter what brand of blades you use on your table saw if you need to replace them. Nonetheless, if you want to change a table saw blade properly, you must know how to do it.

How to Change Blade on Ryobi Table Saw?

To change the blade on a Ryobi table saw, first remove the blade by pushing down on the release button and pulling it out. Then, remove the old blade by sawing it off with a sharp knife.

The information provided in this post will guide you through the process of changing the blade on your Ryobi table saw. Hence, if you have a question related to changing blades, keep reading.

See Also: How to Unlock a Ryobi Table Saw?

ryobi table saw blade change Step by Step Guide

The following steps will show you how to properly change a Ryobi Table Saw Blade. Follow these steps to get started:

  • Gather the Required Tools
  • Remove the Old Blade
  • Install the New Blade
  • Adjust the Blade
  • Test the New Blade

Step 1: Gather the Required Tools

To change the blade on your Ryobi table saw, you will need to gather a few tools beforehand. You will need a hex key wrench, a brush or compressed air, and a new blade. Make sure to unplug the saw before starting this process.

Step 2: Remove the Old Blade

  1. Unplug your Ryobi table saw from its power source.
  2. Raise the blade of the saw to its highest position.
  3. Loosen the arbor nut that holds the blade in place with a wrench.
  4. Remove the old blade from the arbor.
  5. Inspect the arbor for damage and clean any debris from it.

Step 3: Install the New Blade

  1. Select a new blade that is appropriate for the cutting you will be doing and compatible with your Ryobi table saw.
  2. Install the new blade onto the arbor, ensuring it is tight against the flange.
  3. Use a wrench to tighten the arbor nut to secure the blade.
  4. Lower the saw’s blade to its lowest position and plug in the power source.
  5. Test your new blade by making a few cuts on a piece of scrap wood before moving on to your project piece.

Step 4: Adjust the Blade

The blade is adjustable if your Ryobi table saw is anything like mine. To change the blade, loosen the two bolts holding the blade in place.

Next, remove the old blade and replace it with the new one. Finally, tighten the bolts back up, and you’re all set!

Step 5: Test the New Blade

If you’re a woodworker, you know how important it is to have a sharp blade on your table saw. A dull blade can ruin a piece of wood and be dangerous to work with. That’s why it’s essential to know how to change the blade on your Ryobi table saw.

First, you’ll need to unplug the saw and ensure it’s turned off. Then, raise the blade to its highest position and loosen the arbor nut with a wrench. You should be able to do this by hand, but if it’s too tight, you can use an impact driver.

Once the nut is loose, you can remove the old blade and install the new one. Be sure to line up the teeth of the new blade with the slot in the arbor. Once the blade is in place, tighten the arbor nut until it’s snug.

Finally, plug in the saw and turn it on. Make a few test cuts to ensure the blade is installed correctly and cutting properly. You’re ready to get back to work if everything looks good!

How to adjust the blade on a Ryobi table saw?

Like most people, you probably don’t think about changing the blade on your Ryobi table saw very often. But if you use your saw regularly, or if it’s been a while since you’ve changed the blade, it’s essential to know how to do it properly. Here’s a quick guide on adjusting the blade on a Ryobi table saw.

First, unplug the saw from its power source. Then, raise the blade to its highest position and lock it. Next, remove the throat plate by loosening the two screws that hold it. Be careful not to drop the screws, as they can be challenging to find if they fall into the saw.

Once the throat plate is removed, you’ll be able to see the arbor nut. Use a wrench to loosen the arbor nut and remove the blade from the saw. To install a new blade, reverse these steps.

Be sure to tighten the arbor nut securely before using the saw again. With these simple instructions, you should be able to change the blade on your Ryobi table saw with no problem.


In conclusion, By removing the blade guard and inserting a Phillips head screwdriver into the blade hole, Ryobi table saw blades can be replaced. Knowing how to change a table saw blade will be useful when you need to do so in the future.

Similar Posts